GMJ Automotive LLC

Hey Adams County , are your tires worn out? What is the standard for our Wisconsin streets? How can you tell on your sedan ?

While there may be legal requirements for the Adams County area, there are safety concerns that go beyond meeting minimum replacement mandates.

2/32 is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there’s just 2/32 of an inch – 1.6 millimeters – of tread left. It’s that level of wear that’s been called into question recently.

We’re referring to the Consumer Reports call to consider replacing tires when tread reaches 4/32 of an inch, or 3.2 millimeters. And the recommendation is backed by some very compelling studies.

The issue is braking on wet surfaces in and around Adams County . Most of us think of our brakes doing most of the work, but if you don’t have enough tread on your tires, the brakes can’t do their job. When it’s wet or snowy, the tread of the tire is even more critical to stopping power.

Picture this: you’re driving over a water covered stretch of road near Adams County , Wisconsin. Your tires must be in contact with the road in order to stop. That means that the tire has to move the water away from the tire so that the tire is actually contacting the road and not floating on a thin film of water.

Floating on the surface of water is called hydroplaning. So if there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

In the study a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up were brought up to 70 miles per hour, or 112 kilometers an hour and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:

• New tire tread depth
• 4/32 of an inch
• 2/32 of an inch

So what happened with the 2/32 tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 miles an hour. Stopping distance was nearly doubled to 379 feet and it took 5.9 seconds.

Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 miles an hour with the worn tires.

Now, with the partially worn tires – at 4/32 of an inch – the car was still going at 45 miles an hour at the point where new tires brought the car to a halt. It took nearly 100 feet more room to stop and 1.2 seconds longer. That’s a big improvement. We can see why Consumer Reports and others are calling for a new standard.

Of course, stopping distances were greater for the heavier pick-up truck.

How do you know when your tires are at 4/32 of an inch? Easy; just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

You may remember doing that with pennies. A penny gives you 2/32 to Abraham Lincoln’s head. The quarter is the new recommendation – 4/32.

How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?

For us, and we would guess for many, the answer is “no”.

GMJ Automotive LLC
230 W Liberty St
Adams, Wisconsin 53910
608-339-3834

So you love our job, and your family life is great: You have achieved balance. But can you the same for your wheels? You can tell if your tires are out of balance by vibrations at higher speeds. If one of the front tires is out, you feel the vibration in the steering wheel. If it’s a back tire, you’ll feel the vibration in your seat.

Tires and wheels are pretty heavy. When a tire is mounted on a wheel, it is usually not perfectly balanced. So the tire technician will spin the tire on a machine to determine where it’s too heavy. He will then place weights on the wheels in strategic locations to balance it out. When a tire is out of balance, it actually bounces down the road instead of rolling smoothly. Since the average size tire rotates at about 850 revolutions per minute at 60 MPH, it is actually slamming into the pavement 14 times a second. That’s where you get your vibration.

Most people are surprised at how smoothly their car rides after balancing all four wheels.

Most high-quality tires hold their balance pretty well. They just get out of balance gradually with normal wear and tear. If you suddenly feel a vibration, it is probably because you lost a wheel balancing weight along the way. Definitely get a balance if you feel a vibration, change your rims or have a flat repaired. Putting off a needed balance job leads to excessive tire wear, wear to your shocks, struts, steering and suspension parts. wheel balancing not only improves your ride and handling, but also can save you some big repair bills and possibly an accident. Additionally, you will get better gas mileage.

Some people have their tires balanced at every rotation. Others do it every other time. Check your owners’ manual for your requirements, or ask your technician. Doing thus will put you on the path to mechanical wheel balance

.

Let me start by saying that your wheel bearings keep the wheels on your vehicle. Did that get your attention? In this article we’ll discuss more about wheel bearings and how you can keep them doing their very important job while you drive around Adams Wisconsin.

Come see us at: 230 W Liberty St Adams, Wisconsin 53910

Wheel bearings are pretty simple parts. They’re made of high quality steel and are engineered to last 100,000 miles or more if properly cared for. The bearings do two very important jobs: First they allow the wheel to freely rotate with as little friction as possible. Second, they support the weight of the vehicle. For example, if your car weighs 3,600 pounds, each wheel has to support approximately 900 pounds. That’s a lot of heavy lifting over many, many thousands of miles.

Even though wheel bearings are relatively simple, they need to be in near perfect condition to do their job. The bearings are packed with heavy grease to lubricate and protect them. A seal keeps the grease in and water and dirt out. It’s when the seal starts to leak that problems begin. The grease can become contaminated; causing the wheel bearings to overheat and ultimately fail.

The first sign that your wheel bearings are in trouble is an unusual noise coming from a wheel. It could be a chirping, growling, rumbling or a cyclic sound. The noise could get louder or even disappear at certain speeds. Your technician at GMJ Automotive LLC can inspect for bearing wear by lifting the vehicle and checking for play in the wheel.

Now some wheel bearing assemblies are factory sealed. That means that they cannot be serviced – they can only be replaced. Those that aren’t sealed can be serviced on schedule. The bearings are removed, cleaned and inspected. If the bearings are still good, they’re re-installed – if not, they’re replaced. They are then packed in grease and a new seal is installed.

If your vehicle has a factory sealed wheel bearing assembly, the entire assembly needs to be replaced when trouble arises. Unfortunately, the parts are pretty pricy – but they usually last about 150,000 miles as long as the seals hold up.

Now, even a good seal cannot keep out water that’s exerting pressure on the seal. So if you’ve driven through hub deep water your bearings should be cleaned and repacked if they’re serviceable. If you have factory sealed bearings, you just need to watch for signs of premature failure.

If your wheel bearings can be serviced, your owner’s manual will recommend an interval, usually around 30,000 miles.

Now, if you have any sort of trailer, don’t forget its wheel bearings. They probably need to be serviced even more frequently. This is especially true for boat trailers that are used to launch the boat by backing it into the water. These should be serviced every year, usually at the end of the season so that the bearings don’t have the opportunity to sit and rust all winter.

So what happens if wheel bearings fail? Well, the wheel can literally fall off the vehicle. I don’t need to tell you how bad that could be. So check with your service advisor at GMJ Automotive LLC and see if your vehicle’s wheel bearings can be serviced and when it’s recommended. Listen for warning signs. If you’ve been fording streams or puddle surfing after rainstorms, be especially vigilant.

Come by GMJ Automotive LLC for a wheel bearing inspection, or for maintenance services . Call for an appointment at 608-339-3834

Some of us just love tires. All those little rubber hairs on new tires and the smell is wonderful. We live in a great time for tires. No matter how you drive, where you want to go or the look you’re after; there is a tire for you.

The same is true about wheels. The hardest part is choosing from the thousands of wheels available.

We may not be able to help with that, but we can help you get some things in mind before you consult with your Adams tire professional. Let’s start with function and think about how you drive.

For example, maybe you have a large SUV but you don’t drive off-road, so an off-road tread isn’t important. Also, because you are not out bouncing over rocks in the Wisconsin backcountry, you don’t need a high profile tire to protect your rims. So that means you can probably go with the low-wide look.

If you have a winter season with rain and snow or if you find you need better ice and snow performance, they make great, high-performance snow tires that won’t make it look like you are driving a tractor.

There really are a lot of options for any given vehicle. You will find it very helpful to have a discussion like this with your Adams County tire pro when you need new tires. You can find the best solutions for your driving needs and to make improvements in ride or handling.

Picking a wheel that is the same size as what you are now running is pretty simple. But, it gets trickier if you want to upsize. Just get some help when you go bigger. All that tire and wheel still needs to fit in the available space. You do not want your tires to rub when you turn or hit a bump. You also need to make sure your brakes and suspension bits will fit with your wheel of choice. It doesn’t matter how great your car looks if it’s not drivable.

Taller, wider wheels and tires probably weigh more than your stock shoes. And it’s “unsprung” weight – that has a big impact on brake performance. The upsized shoes increase rotational inertia – if you go too big you may need to upgrade your brakes to compensate.

Another possible problem is an inaccurate speedometer. This happens because the number of rotations can change with the new wheels. Fortunately, speedometers and odometers are all controlled by the engine computer; so it is simple to get it reprogrammed and compensate for the bigger tires.

No matter what you are after: low cost, long life, high performance, traction or stunning good looks, your wheel and tire professional at GMJ Automotive LLC in Adams, Wisconsin can help you identify your needs and give you a custom fit. With all the options available, you don’t have to compromise. There is a tire out there with your name on it!